Hercules Barrel Handling Solutions

Morse PailPRO Can Tumblers provide aggressive corner-over-corner mixing action. Mix products right inside your sealed cans or pails with these can rotators to reduce hazards and save clean-up. Use your pail and can mixer to blend the contents of closed 1 to 5 gallon (4 to 20 liter) pails or cans .

Key features

• Morse 5-Gallon Can Tumblers mix or agitate small batches quickly and economically
• Re-homogenize settled ingredients
• Use as pail or bucket mixer to blend liquid or dry materials
• Tumble pails of parts with media to deburr or polish them
• Tumble steel or plastic can or pail with up to 12.5" (31.75 cm) diameter, and from 4.5" to 16.5" (12 to 42 cm) tall. Includes typical 5-gallon (19 or 20 liter) cans.
• Capacity: 100 Lb. (45.5 kg) per can
• Tumbling Speed: 23 RPM (19 RPM on 50Hz models)
• 1-305 Series rotates one can at a time
• 2-305 Series rotates one or two cans at a time
• Morse 5-Gallon Can Tumblers rotate in one direction only; they do NOT shake or oscillate cans
• 1/4 HP, 60Hz motor in choice of voltage, phase, TEFC or explosion-proof (50Hz models also available)
• Air motor also available
• IMPORTANT: OSHA requires enclosure with interlock
• Guard Enclosure Kit is sold separately
• For larger pail or can, order with Option # XLC-1-305 for single can tumbler, or Option # XLC-2-305 for double can tumbler

Morse PailPROTM Can Tumblers rotate a closed pail or can "corner over corner" to thoroughly mix contents. Mix or agitate small batches quickly and economically

• Re-homogenize settled ingredients
• Blend liquid or dry materials
• Tumble parts with media to deburr or polish

Can Tumblers provide exceptional savings when materials to be agitated are already packed in cans.

Quickly secure pail in can holder with hand wheel and locking handle.

1-305 Series SINGLE Can Mixers rotate one can at a time.

2-305 Series DOUBLE Can Mixers rotate one or two cans at a time.

IMPORTANT: OSHA holds the employer responsible for the suitability of design and application of tools and machinery.
Install all Morse Rotators in accordance with requirements for enclosure and safety interlock, etc. One way to accomplish this is with a Morse enclosure with safety interlock, so the rotator automatically turns off when enclosure door is opened. Power connections and motor controls must also comply with applicable local codes.

For OSHA compliance in the USA, see OSHA subpart O.1910.212(a)(4) "Barrels, containers, and drums. Revolving drums, barrels, and containers shall be guarded by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place."


Motors on Morse 5-Gallon Can Tumblers are 1/4 HP, 60Hz in choice of voltage, phase, TEFC or explosion-proof (50Hz also available). Single-phase, 115V TEFC version on model 1-305-1 or 2-305-1 includes a timer you set at 1 to 60 minutes for automatic shut-off. Timer is NOT available on other 5-Gallon pail mixer models.

Air motors are also available. Air motors are vane-type and require correctly sized filter, regulator, lubricator, valve (FRL) and piping supplied by customer. FRL for air powered pail mixer may be ordered from Morse.
Part # 90010-P - Description: KIT, 1/4" FRL & VALVE
Part # 90020-P - Description: KIT, 3/8" FRL & VALVE

All other Morse can tumblers are shipped without control, cord and plug, and must be installed by an electrician according to local codes and customer''s preference.

Explosion-Proof motors are rated for Class I Group D, and Class II Groups F and G.

Tilt-To-Load Drum Tumbler
with Automated Control Package
and Safety Enclosure
Automatically lifts your drum, rotates it for the time you set,
then returns it to upright at floor-level
Tilt-To-Load Drum Tumblers with the advanced factory-installed Automated Control Package to automatically lift your drum, rotate for the time you set, and then return it to upright position at floor-level for easy handling. The built-in safety interlock on the enclosure automatically shuts off the drum rotator when the gate is opened. Watch the video to see how it works.

Set the desired time of drum rotation anywhere from a few seconds to 16 hours, push the start button, and walk away. You preset the tumbling speed from 5 to 20 RPM. 

The enclosure has an integrated safety interlock, in accordance with OSHA requirements, so the machine automatically shuts off when the enclosure is opened.

problem during operation, the tumbler can be interrupted by hitting the red emergency stop knob.

 

Tumble a steel, plastic or fiber drum from 29" to 37" tall, and from 18" to 23.5" in diameter.

 

 

 

Enclosure outside post-to-post Dimensions:
L88" x W52" x H63.25"
(224 x 132 x 161 cm)

 

The Drum Holder on Morse
Tilt-To-Load Drum Tumblers
Supports drum on a base plate under the drum,
two clamps on top of the drum, and
a web strap and ratchet around drum.

• Tumble drum 29" to 37" (74 to 94 cm) tall
• Tumble drum 18" to 23.5" (46 to 60 cm) in diameter
• Variable speed: 5 to 20 RPM
• Capacity:
  • 800 Lb. (363 kg) full drum
  • 400 Lb. (181 kg) half-full drum. Half-Full Drum Rating is an indication of the capacity for tilting an unbalanced, bottom-heavy drum. A partially full drum with an unbalanced and shifting load is harder to tilt than a full drum.

 

 

IMPORTANT - OSHA holds the employer responsible for the suitability of design and application of tools and machinery.
Install all Morse Rotators in accordance with requirements for enclosure and safety interlock, etc. One way to accomplish this is with a Morse enclosure with safety interlock, so the rotator automatically turns off when enclosure door is opened. Power connections and motor controls must also comply with applicable local codes.

For OSHA compliance in the USA, see OSHA subpart O.1910.212(a)(4) "Barrels, containers, and drums. Revolving drums, barrels, and containers shall be guarded by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place."

Additional Information:

• Delivery Time: 12 to 14 weeks
• Packaging Details: crate

Tilt-To-Load Drum Tumblers

Ergonomic POWER-LIFT and vigorous "corner-over-corner" mix inside drum.
NO need to open drum... NO Mess... NO contamination.
Vary drum rotation speed for thorough tumbling action!
Blend valuable ingredients. Save Time, Labor and Money!

Key features

• Rotate a plastic, steel or fiber 30 to 55 gallon (114 to 210 liter) drum
• Blend inside a closed drum to ensure homogeneous, uniform batches
• Remix valuable settled or stratified ingredients
• Smooth rough parts by tumbling with media
• Load upright drum at floor level with drum truck, model 81 Drum Spotter, or a below-hook drum lifter and your hoist
• Rotate drum from 5 to 20 RPM (4 to 16 RPM for 50Hz models)
• IMPORTANT: OSHA requires enclosure with interlock
• Control Package and Guard Enclosure each sold separately
• Capacity:
  • 800 Lb. (363 kg) Full Drum
  • 400 Lb. (181 kg) Half-Full Drum
    Half-Full Capacity is an indication of the capacity for tilting an unbalanced, bottom-heavy drum. A partially full drum with an unbalanced and shifting load is harder to tilt than a full drum.

Morse 310 Series Tilt-to-Load Drum Tumblers rotate a closed drum "corner-over-corner" to thoroughly mix the contents. Morse Tumblers are used to ensure homogeneous and uniform batches, remix valuable settled or stratified ingredients, or smooth rough parts by tumbling with media.

310 Series models rotate a drum from 5 to 20 RPM (4 to 16 RPM for 50Hz models). Motors are 2 HP. Model 310-A is air-powered, and includes air controls.

310 Series Drum Tumblers can accommodate a steel, plastic or fiber drum 29" to 37" (74 to 94 cm) tall, 18" to 23.5" (46 to 60 cm) in diameter, from 55-gallon (210 liter) down to 30-gallon (114 liter).

Drum Tumbler shown mixing a plastic drum.

he ergonomic power tilt control raises the drum to rotating position. Turn the motor on to activate drum tumbler hydraulics. Tilt the drum to top position with the RAISE control valve. Use the second control to start and stop drum tumbling. Begin drum rotation with the ROTATE control valve.

Combine three components to meet safety requirements:

1. Drum Tumbler
2. Control Package (sold separately)
3. Guard Enclosure Kit (sold separately)

OSHA requires a guard enclosure with safety interlock, so that the rotator will automatically stop running if the enclosure gate is opened


IMPORTANT: OSHA holds the employer responsible for the suitability of design and application of tools and machinery.
Install all Morse Rotators in accordance with requirements for enclosure and safety interlock, etc. One way to accomplish this is with a Morse enclosure with safety interlock, so the rotator automatically turns off when enclosure door is opened. Power connections and motor controls must also comply with applicable local codes.

For OSHA compliance in the USA, see OSHA subpart O.1910.212(a)(4) "Barrels, containers, and drums. Revolving drums, barrels, and containers shall be guarded by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place."

NEMA 4/12 Control Box includes Timer, Start and Stop Buttons, Red Emergency Stop Button, Lockable Main Disconnect, and Wire terminals for safety interlock switch. NEMA 7/9 Explosion-Proof Control Box includes Start and Stop Buttons, and wire terminals for external connection of safety interlock switch.

Only NON-Explosion Proof AC Control Packages include a pre-wired control box. Explosion-Proof Control Packages have no wiring from the NEMA 7/9 control box to the motor. Please consult an electrician to complete the wiring in accordance to your local code.

Additional Information:

• Delivery Time: 10 to 12 weeks