Hercules Barrel Handling Solutions

Drum Lifting Hooks for Horizontal Steel Drum

• Lift a horizontal drum with your hoist or crane


• ONLY for horizontal 55-gallon (210 liter) steel drum


• Capacity: 1000 Lb. (454 kg)

These Drum Lifting Hooks are used to lift a horizontal 55-gallon (210 liter) steel drum, 34" to 36" (86 to 92 cm) long. They add 10.6" (27 cm) to the height of your apparatus when lifting a horizontal drum (measured from the drum rim to the inside top of the lifting eye).

Capacity: 1000 Lb (454 kg)

WARNING: Do NOT attempt to lift an upright drum with this device.

Model 41 Drum Lifting Hook has an alloy steel lifting ring, steel rods, and malleable iron hooks.

Model 41M horizontal drum lifter is similar to model 41, but has spark resistant parts

• Rods are stainless steel
• Lifting ring and hooks are spark resistant aluminum/bronze alloy

Morse drum lifters comply with ANSI/ASME B30.20 standard for mechanical, below-the-hook lifting devices as it applies to the following:

• Rated load markings and unit identification
• Minimum design safety factor of 3, based on yield strength, for load bearing structural components
• Welding is performed by certified welders who have passed the ANSI/AWS D14.1 welding qualification test
• All welding is in accordance with ANSI/AWS D14.1 and ASME BTH-1

Drum Lifting Hooks for Horizontal Steel Drum

• Lift a horizontal drum with your hoist or crane


• ONLY for horizontal 55-gallon (210 liter) steel drum


• Capacity: 1000 Lb. (454 kg)

These Drum Lifting Hooks are used to lift a horizontal 55-gallon (210 liter) steel drum, 34" to 36" (86 to 92 cm) long. They add 10.6" (27 cm) to the height of your apparatus when lifting a horizontal drum (measured from the drum rim to the inside top of the lifting eye).

Capacity: 1000 Lb (454 kg)

WARNING: Do NOT attempt to lift an upright drum with this device.

Model 41 Drum Lifting Hook has an alloy steel lifting ring, steel rods, and malleable iron hooks.

Model 41M horizontal drum lifter is similar to model 41, but has spark resistant parts

• Rods are stainless steel
• Lifting ring and hooks are spark resistant aluminum/bronze alloy

Morse drum lifters comply with ANSI/ASME B30.20 standard for mechanical, below-the-hook lifting devices as it applies to the following:

• Rated load markings and unit identification
• Minimum design safety factor of 3, based on yield strength, for load bearing structural components
• Welding is performed by certified welders who have passed the ANSI/AWS D14.1 welding qualification test
• All welding is in accordance with ANSI/AWS D14.1 and ASME BTH-1

Drum Lifting Hooks for Horizontal Steel Drum

• Lift a horizontal drum with your hoist or crane


• ONLY for horizontal 55-gallon (210 liter) steel drum


• Capacity: 1000 Lb. (454 kg)

These Drum Lifting Hooks are used to lift a horizontal 55-gallon (210 liter) steel drum, 34" to 36" (86 to 92 cm) long. They add 10.6" (27 cm) to the height of your apparatus when lifting a horizontal drum (measured from the drum rim to the inside top of the lifting eye).

Capacity: 1000 Lb (454 kg)

WARNING: Do NOT attempt to lift an upright drum with this device.

Model 41 Drum Lifting Hook has an alloy steel lifting ring, steel rods, and malleable iron hooks.

Model 41M horizontal drum lifter is similar to model 41, but has spark resistant parts

• Rods are stainless steel
• Lifting ring and hooks are spark resistant aluminum/bronze alloy

Morse drum lifters comply with ANSI/ASME B30.20 standard for mechanical, below-the-hook lifting devices as it applies to the following:

• Rated load markings and unit identification
• Minimum design safety factor of 3, based on yield strength, for load bearing structural components
• Welding is performed by certified welders who have passed the ANSI/AWS D14.1 welding qualification test
• All welding is in accordance with ANSI/AWS D14.1 and ASME BTH-1

Drum Lifting Hooks for Horizontal Steel Drum

• Lift a horizontal drum with your hoist or crane


• ONLY for horizontal 55-gallon (210 liter) steel drum


• Capacity: 1000 Lb. (454 kg)

These Drum Lifting Hooks are used to lift a horizontal 55-gallon (210 liter) steel drum, 34" to 36" (86 to 92 cm) long. They add 10.6" (27 cm) to the height of your apparatus when lifting a horizontal drum (measured from the drum rim to the inside top of the lifting eye).

Capacity: 1000 Lb (454 kg)

WARNING: Do NOT attempt to lift an upright drum with this device.

Model 41 Drum Lifting Hook has an alloy steel lifting ring, steel rods, and malleable iron hooks.

Model 41M horizontal drum lifter is similar to model 41, but has spark resistant parts

• Rods are stainless steel
• Lifting ring and hooks are spark resistant aluminum/bronze alloy

Morse drum lifters comply with ANSI/ASME B30.20 standard for mechanical, below-the-hook lifting devices as it applies to the following:

• Rated load markings and unit identification
• Minimum design safety factor of 3, based on yield strength, for load bearing structural components
• Welding is performed by certified welders who have passed the ANSI/AWS D14.1 welding qualification test
• All welding is in accordance with ANSI/AWS D14.1 and ASME BTH-1

EasyLift™ ergonomic transporters are available with a variety of fixed or folding jibs available for lifting a variety of objects.  Jibs are available in lengths to suit customer specific applications and are generally sold with 360 degree swivels for rotating the object when lifted.  This equipment is available with manual lift, DC powered lift, AC powered lift,  air powered hydraulic lift, pneumatic lift or 24-volt self-powered models with power travel.

Additional Information:

• Delivery Time: 6 to 8 weeks

The Easy Lift line of keg handling equipment is the safe and ergonomic solution for lifting kegs onto shelving as well as double or triple stacking kegs in congested beer coolers. These units can also be used to load and unload kegs from vehicles. An automatic clamping mechanism lifts the keg by either one of the handles on the upper side of the keg. A 24-volt DC battery system provides enough power to stack over 300 kegs per charge. Large 8" x 2" Darcor casters require minimal starting and continuous push force, making the Easy Lift keg transporter a truly safe and ergonomic machine.

Darcor Ergonomic PD Casters: (2) 8" x 2" rigid. (2) 8" x 2" locking swivel. 

Power lift, gravity down system by means of (2) 12-volt AGM deep cycle batteries, battery discharge indicator, on-board automatic charger and key switch.

Safety yellow powder coated for durability.  Optional: FDA appoved epoxy powder coating or stainless steel construction

Keg Lift heights vary to meet customer requirements.

Capacity: 200 lb.

Our keg lifting equipment offers lift heights are typically 40" or 60" above floor level.  These keg lifts can be built to customer specifications for shelves and door heights. 

19" wide x 30" long

Additional Information:

• Delivery Time: 4 to 6 weeks

We can customize clamps with or without rotation features to suit your specific application.  Should your requirement be to handle circular shapes from hot ovens, cylinders, rolls, drums or require an ergonomic method for gripping and stacking bales, we can provide a solution.  Clamps can be installed on manually propelled base frames with straddle legs, manually propelled counter-balanced base frames or our most ergonomic power travel base frames.

A Safe and Easy Solution to your Cylinder Handling Needs

For more than 30 years, Easy Lift Equipment has been providing customized solutions to clients with specific material-handling needs. Our products are designed to minimize risk and improve productivity in a wide range of environments, from warehouses and shipping hubs to manufacturing facilities. Easy Lift clamps provide a safe way to handle sensitive container manufacturing facilities. Easy Lift clamps provide a safe way to handle sensitive containers such as compressed gas cylinders.

Investing in a compressed gas cylinder lift gives your staff a safe way to avoid dangerous manual handling of cylinders such as those containing CNG (compressed natural gas). Our clients have found that safer employees are also more productive — your initial investment in a custom cylinder lift will be returned through less downtime and improved efficiencies.

The photos shown on this page display one of our pieces of gas cylinder handling equipment provided to solve customer handling problems.

Built and Tested in Newark, DE

 

All of our custom cylinder handling equipment is made in our Newark, DE facility. All of our equipment undergoes thorough quality control testing to ensure each unit meets our rigorous quality control standards. The photos shown on this page display examples of some of custom gas cylinder handling equipment  we have provided to for our customers' cyu. To learn how we can customize a cylinder lift or clamp to your specific needs, contact our team today.

Standard features for all pieces of cylinder handling equipment include:

Darcor 5" x 2" PSE ergonomic casters 

Step-down foot floor locks for added safety 

Safety orange powder coating or FDA approved powder coating  finish with stainless steel hardware or stainless steel construction.

The CCR cylinder clamp is a clamp for gripping and rotating cylinder shaped containers from 13"/ 330 mm to 8”/ 203 mm to in diameter. The pinned stationarypad can be adjusted forward for handling container diameters less than 8”/203mm. The clamping pads are 16”/406 mm in overall height to provide greater surface area on the cylinder. This CCR clamp is available in a rotating or nonrotating version and can be added to any Air powered, DC powered or AC powered model.

Additional Information:

• Delivery Time: 8 to 10 weeks

In applications requiring kegs to be rotated for filling or for horizontal or vertical keg storage, special keg clamp rotators are used as shown in the next few images and video. 

The unique single moving arm permits horizontal stacking of kegs with minimal spacing required between other kegs.

The lift height is specific to the customers application.  EasyLift beer keg lifters can be finished in FDA approved epoxy powder coating, with stainless steel construction available as an option.

Darcor Ergonomic PD Casters: (2) 8" x 2" rigid. (2) 8" x 2" locking swivel. 

Foot Floor Lock for added safety.

Power clamp, lift and 360 degree rotation

(2) 12-volt AGM deep cycle batteries, 24 volt system, with automatic charger, key switch, battery and discharge indicator.

Red deadman safety switch to prevent accidental opening of clamp.

Powder coated for durability with an FDA appoved epoxy powder coating

 

Clamps and lift heights vary to meet customer requirements.

Capacity: 200 lb.

Lift heights vary to match customer requirements (shown with 32" of lift)

Clamping pad height typically 4".

Dimensions of model shown: 34" long x 27" wide X 90" tall (for horizonal stacking 4 high)

 

Machine height is made to customer specifications and requirements.

Additional Information:

• Delivery Time: 6 to 8 weeks
• Packaging Details: Crate